Outside wall ceramic tile adhesive using method

Ceramic tile adhesive is a very important material, many people choose these materials are not take advantage of the ideal, cause the effect is not obvious, after the repair work is also very trouble. You can see ceramic tile glue to stick wall using method as well as the use of ceramic tile adhesive matters needing attention in the construction, selection methods and techniques to various kinds of ceramic tile adhesive, after has the advantages of better too much and also won't appear the quality problem of the negative. Ceramic tile adhesive stick wall using method using ceramic tile adhesive matters needing attention in construction are used in ceramic tile glue stick a construction method of use the building attention ceramic tile ceramic tile adhesive glue stick use tile glue stick a wall to be basic level processing, and then put a raise and wall tile adhesives, clean up the surface of wall brick, the glue daub on it. 1, the basic level processing before the shop is stuck wall brick, we need to carry on the basic level processing. Grassroots clean up dirt and stains on the surface of the first, and then in the putty layer on the surface of the coating layer and remove clean. At the same time, also cope with the grass-roots flatness check, if, at the grass-roots level is also need to use cement mortar leveling, otherwise it will affect the effect of brick wall brick. 2, lofting and grassroots clean, also cannot be directly laid wall brick, but should first around the wall with chalk line pops up a few elevation control line, and popup reticle in the ground, control the size of each piece of floor tile. Then will be before paving tiles according to the requirements of decoration, check and adjust the effect that decorate. 3, modulation wall brick binder in binder paste to add the appropriate moisture, mixed them evenly stirring, and it let stand for five minutes to ten minutes, then stir it came into use 1 to 2 minutes. 4, clean up the brick wall surface modulation good adhesive, you can begin to prepare brick wall brick. In front of the shop is stuck, for wall tile dust and dirt on the surface of the product to clean up. After clean, and can be configured in advance paste daub is on the back of ceramic tile, pay attention to when daub sizing agent to apply evenly and full. 5, the shop is stuck of slurry wall brick wall tile will be wiped out shall be carried out in accordance with the before paving pattern style before the shop is stuck, after the shop is stuck is flat and level, take with a rubber hammer to tile, enhance its stability. At the same time, in the process, but also turns a little bit about the wall brick, make good contact with ceramic tile on the back and paste, closer integration. 6, lumbar line brick many performance in order to increase the adornment of metope, can choose to use the waist line. At the waist line of the shop is stuck, should not only pay attention to keep the consistency of the texture and wall tile, but also have a certain gap, for sealing or beautiful sewing processing, otherwise it's easy to do more harm than good. 7, sealing treatment after the shop is stuck wall brick after 24 hours, can sew modulation good sealing agent or the agent daub of cracks in the brick and the brick, prolong its service life, increase the overall aesthetics of indoor decoration. After sealing when processing is complete, with a soft cloth to clean up the extra sealing agent, maintain the cleanliness of the surface of the brick wall. Use ceramic tile adhesive matters needing attention in construction of 1, the key lies in the use of professional construction tools using professional ceramic tile adhesive tooth scraper with major construction. Different specifications and types of the ceramic tile ceramic tile with different adhesive glue, different specifications of ceramic tile chooses different tooth type scraper. According to the standard of the industry, tooth width 4 mm is suitable for the Mosaic, 6 mm is suitable for the outer skin brick wall paper, 10 mm is suitable for general bo changes a brick, tooth width 12 mm is suitable for large vitrified tiles and marble with the shop is stuck. 2, ceramic tile adhesive base before construction to check check base layer for easy to fall off items, to clean up dust and debris on the surface of the base, avoid brick after the shop is stuck ceramic tile causes because of base level dust fall off. 3, use ceramic tile adhesive manufacturer recommends the water cement ratio of mixing manufacturers recommend water-cement ratio is obtained after strict test product performance guaranteed data, according to the packing recommended water ratio, using electric mixer will stir paste paste evenly, no particles, let stand for 5 minutes then stir 1 to 2 minutes. Above introduction is glue stick wall ceramic tile using method as well as the use of ceramic tile adhesive matters needing attention in the construction, a lot of people are found in the process of using ceramic tile adhesive is easy to damage, or there is no use in place, lead to paste the effect is not very good. You can focus on the construction process with all kinds of considerations, such as to choose the right construction tools, and then in the construction material to check before using and so on.
Guangdong Overland Ceramics Co., Ltd has built its reputation on a commitment to providing quality products and services while rapidly responding to international needs for innovative products.
The guiding vision of Guangdong Overland Ceramics Co., Ltd is 'Bringing the best to everyone we touch'. By 'The best', we mean the best products, the best people and the best ideas.
To strengthen and grow our leadership position by providing tile company across a range of market segments, including ceramic floor tile, and high-performance servers.