So the bathroom tile shop sticks from the shop before the shop is stuck, need to pay attention to the first part has a lot of process specification, then the bathroom ceramic tile ceramic tile, including ceramic tile metope and ground, so the following will introduce the bathroom
floor tile specification requirements.
Bathroom floor tile process specification before 1 specification requirements, specifications, the wall brick of toilet should not have too big wall brick specifications can give a person a sense of disharmony, and adornment effect is better is the small size of wall brick, bathroom wall brick specification now basically has 300 * 400 mm, 300 * 300 mm, 250 * 330 mm, 200 * 300, 250 * 330, 450, 300 * 300 * 600.
2, brick for to do well in front of the shop is stuck, less than the extra narrow columns do not appear as far as possible.
Really must processing cutting, ceramic tile after cutting with the rest more than two thirds of the advisable.
3, before the shop is stuck remember conduit wire to metope, the circuit, water go chart to keep well.
And be sure to conduct a water closed, closed electricity experiment, lest appear slack, leakage.
Bathroom floor tile 1 specification requirements in the process specification, mixed with toilet wall brick used in cement is 425 tags for cement, the mixing proportion of cement sand don't more than 1:3, the cement content is overweight, leads to the wall because of the high coefficient of expansion of cement and brick cracking, reduce the service life of
wall tile.
2, toilet if the glazed wall tile, cement mortar was used as adhesive, ceramic tile to the shop is stuck, after bubble water bubble water after soaking time in ceramic tile completely without risking bubble time advisable, generally for 30 minutes.
3, the shop is stuck whether belong to the seamless brick wall brick, toilet must be seam, suggest not less than 1 mm, ordinary wall tile to 1.
5 -
It is advisable to 2 mm, archaize brick gap could widen the appropriate.
4, pay attention to the texture of ceramic tile shop sticks ceramic tile, do long grain brick, tile waist line is to pay attention to the direction of the positive and negative direction, don't put down, tiling of lumbar line brick texture and texture.
As shown in figure 5, toilet wall brick floor height is higher than the height of the ceiling, is generally not less than 10 centimeters advisable.
Bathroom floor tile after process specification requirements specification 1, ceramic tile after the shop is stuck on the ground, must wait for the ground dry solid to walk on surface of the brick or other hutch is defended decorate a project.
2, the general is the use of colorful caulking agent to fill, is typically used for pavement seam metope, its characteristic is colour is good adhesion, compression wear-resisting, not not alkalify, contractive, not pulverization, not only changed the wall brick gap is easy to fall off, adhesion not firm problem, also make the color of aperture and ceramic tile appear unified and harmonious suitably.
3, tick off seam need to ceramic tile of the reentry after dry solid is advisable.
It is advisable to generally within 24 hours after.
4, after the shop is stuck, be sure to check wall brick empty drum, how to appear the phenomenon of empty drum we can use the glass sucker wall brick suck up to the shop is stuck, must make metope, on the base of the cement layer to do after looking for hair, brick wall brick.
Bathroom toilet of ceramic tile brick specification requirement is introduced here, each has its adjacent due process specification should pay attention to.
Whether it's your own decorate a company to shop sticks ceramic tile, or seek to do coolie, the shop is stuck in the process of ceramic tile specification is clear to yourself and stepping in to do a good job of supervision and acceptance.
Guangdong Overland Ceramics Co., Ltd thinks that that firms can avoid the artificial choice between quantitative and qualitative risk management, allowing both to play important roles in surfacing and assessing risks.
Guangdong Overland Ceramics Co., Ltd works hard to enhance continuously our reputation for accessibility, professionalism, performance, and the depth and quality of our long-term consultative relationships with clients.
Getting tile company from an idea to production is a complex process. It involves significant research, time, planning and patience. But with the right information, the right resources and the right product, it's possible.
Guangdong Overland Ceramics Co., Ltd understands how essential it is to offer ample options, such as tile companyceramic floor tile to afford high-quality products for customers.
Guangdong Overland Ceramics Co., Ltd has a number of producing line for producing tile company.
